October 2011 – Battery Education

Amazon Kindle 3 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

1. Begin by turning your Amazon Kindle 3 face down. Placing your Kindle 3 on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off back cover by detatching the clips that holds the cover on. You will need to slide the pry tool around the entire back cover. After the clips have been detached slide the cover downward and the cover will then come off.

3. Once the back cover is off you will see the inside of the Kindle and the battery.

4. Next remove the 2 screws securing the battery.

5. Remove the original battery.

6. Replace the original battery with the your new Amazon Kindle 3 Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place. You will need to be sure to snap the cover in completely.

9. Charge your new Kindle 3 Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle 2 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle 2 Battery

1. Begin by turning your Amazon Kindle 2 face down. Placing your Kindle 2 on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off the upper grey portion of the Kindle to reveal 2 small screws.

3. Once the upper portion is removed you will see two small screws on either side of the Kindle at the base of the cover. Please remove the screws.

4. Next use the pry tool to press down on the two plastic clips to release the cover. Once the clips are pressed down, lift off the cover to reveal the battery.

5. Remove the two screws securing the battery. Then using the prytool lift up the original battery.

6. Replace the original battery with the your new Amazon Kindle 2 Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place.

9. Return the two screws to hold the cover into place.

10. Return the upper grey portion of the Kindle.

11. Charge your new Kindle 2 Battery for at least 4 hours. Then turn on and use.

Amazon Kindle 1 Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle 1 Battery

1. Begin by turning your Amazon Kindle 1 face down.

2. Slide the grey back cover off of the Kindle.

3. Gently lift the original battery out of the battery compartment and disconnect.

4. Place in the new Amazon Kindle 1 battery replacement and connect it to the battery connector.

5. Replace the grey back cover.

6. Charge your Amazon Kindle 1 for 4 hours.

Garmin Edge 605 Battery Replacement Instructions

The following Garmin Edge 605 Battery Replacement Instruction guide can be used for the following models:

Garmin Edge 605 Battery and replacement kit

1. Begin by turning your Garmin face down and then remove the 6 screws on the back of your Garmin Edge 605.

2. Next using the pry tool carefully pry apart your Garmin casing using the shim/pry tool provided (this may take running the pry tool around the seams a couple of times but it will separate). Or you can grab both halves and carefully pull open. Do not pull completey apart as the battery cable is connected to circuit board.

3. Again as you open the 2 halves do not completely pull them apart as there will be connectors you will need to detach. One of the connectors is the battery connector. Remove the connector attached to the circuit board first. Then revovbe the battery connector. Once these connectors are detached you will be able to separate the 2 halves completely.

4. Now using the pry tool again remove the original battery (it is held down by an adhesive so pry with a gentle firmness)

5. Next place a piece of double sided tape in the battery compartment (this will hold down the battery so it does not move around on you)

6. Next place on the tape the new Garmin Edge 605 battery replacement.

7. Reconnect the connectors from step 3.

8. Next place the 2 sides together and gently snap the device shut (snap all the way around).

9. Next Replace the 6 screws you took out.

10. Next charge your Garmin Edge 705 for 4 hours.

Sony PRS-600 Battery Replacement Instructions

The following Sony PRS-600 Battery Replacement Instruction guide can be used for the following models:

Sony PRS-600 Battery

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the two screws located on the back of your device.

3. Next detach the clip holding the back cover. Use your pry tool to help detach the clip. The clip is the the long back piece that runs the length of your Sony and is the piece held in by the 2 screws your just removed.

4. Next remove the back cover to reveal the inside of your Sony and the battery.

5. Remove the original battery and disconnect the battery cable from the circuit board. . The pry tool will help you lift the old battery out.

6. Replace and connect the new Sony PRS-600 Battery and place into the battery compartment (where you took the original out of).

7. Now let's reverse our steps. Replace the back cover so that it snaps in to the long back clip.

8. Replace the 2 screws on the clip.

9. Charge your battery for a four hours. Then turn on your Sony.

TomTom One 130S Battery Replacement Instructions

The following TomTom One 130 S Battery Replacement Instruction guide can be used for the following models:

TomTom One 130S Battery

1. Begin by removing the faceplate to reveal four screws. To remove the faceplate use the pry tool to lift the face plate up.

2. Remove the four screws using your screw drivers included in your tool kit.

3. Next carefully lift the screen mount plate and rubber shield around the screen off your screen. Lifting from the base of the screen will help accomplish this. Use your pry tool to accomplish this.

4. To access the battery you will need to remove the three screws securing the TomTom's circuit board. One of the screws is under the screen's ribbon cable.

5. Once the circuit board screws are removed you will be able to carefully lift the circuit board and disconnect the battery cable from the board.

6. Once the battery cable is disconnected you can gently pry out the original battery.

7. Connect the new TomTom One 130S Battery and place into the battery compartment (where you took the original out of). It would be helpful to secure the new battery with a strip of double sided tape.

8. Replace the circuit board to its original position and replace the circuit board screws.

9. Replace the screen on top of the circuit board.

10. Replace the screen shield and the screen mount plate around and onto of the screen.

11. Replace the 4 screws you removed in step 2.

12. Attach the faceplate of your TomTom.

13. Charge your battery for a four hours. Then turn on your TomTom.

TomTom XXL IQ Battery Replacement Instructions

The following TomTom One Battery Replacement Instruction guide can be used for the following models:

TomTom XXL IQ Battery

1. Begin by lifting the ends of the label up off your TomTom (this will be on the bottom). You can use the prytool that comes in the kit to do this. The 2 screws are under the ends of the label (one screw under each end).

2. Remove the screws using your torx drivers included in your tool kit.

3. Once the two screws are removed taky your pry tool and insert between the two halves of the Tom Tom and run it around the edge of the TomTom to help separate the two sides. Once you work all the way around the TomTom you will be able to separate the two halves. Please be careful to not pull the two sides to far apart as they are connected by a ribbon cable on the inside. This ribbon cable does not need to be removed to see the battery.

4. In order to gain access to the battery you must remove the three screws securing the circuit board.

5 Once the screws are removed you will be able to carefully lift the circuit board and disconnect the battery cable to the board.

6. Once the battery cable is disconnected you can pry out the original battery.

7. Connect the new TomTom XXL IQ Battery and place into the battery compartment (where you took the original out of).

8. Replace the circuit board and screws.

9. Then put the two halves together. The two sides will snap gently into place.

10. Replace the 2 screws you removed in step 2 and smooth down the label.

11. Charge your battery for a four hours. Then turn on your TomTom.

TomTom One Battery Replacement Instructions

The following TomTom One Battery Replacement Instruction guide can be used for the following models:

TomTom One

1. Begin by laying the TomTom One on its face and remove the four Torx size screws from rear using a proper Torx bit.

2. Next – carefully insert the pry tool between one side of the black back cover and the silver front to a depth of NO MORE than 3 to 4mm. Start to pry the back cover away. Continue working down the side. Repeat for the other side. If necessary also pry at the center of the top. The rear black cover will be released. Take care not to pull it away, as there are two sets of wires with miniature connectors, connecting the battery and loudspeaker on the back cover to the main unit.

3. Once the two halves are apart and laying next to each other, gently disconnect the battery.

4. The battery is secured in the battery recess with a very sticky pad underneath. using the pry tool lift the battery out (remember the battery is held on by an adhesive so you will need to work here a little). Gradually pull the battery away working from side to side. Don’t rush this or damage to the back cover could occur. Retain the sticky pad for reuse, replacing it in the recess.

5. Position the new TomTom One battery into the recess making sure the wire leads exits the recess at the bottom (loudspeaker side) corner.

6. Carefully reconnect the the new battery plugs to the main unit.

7. Replace the two halves of the TomTom and gently snap shut.

8. Replace the 4 screws.

9. Charge your battery for a four hours. Then turn on your TomTom.