March 2012 – Battery Education

SkyGolf SkyCaddie SG5 Battery Replacement Instructions

The following are the SkyGolf SkyCaddie SG5 Battery Replacement Instruction guide.

1. Begin by laying your Skycaddie SG5 face down.

2. Loosen the battery cover screw and gently pull back the rubber USB cover.

3. Remove the old battery.

4. Replace the old battery by inserting a brand new SkyGolf Skycaddie SG5 Battery from BatteryShip.com. The battery will be inserted at an angle so be sure to align the two pegs on each side of the battery with the channels on the SkyCaddie. Slide the battery down to snap it into place.

5. Replace the battery cover.

6. Charge your new battery for four hours. Then turn on your SG5.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

SkyGolf SG2 Battery Replacement Instructions

The following are the SkyGolf SG2 Battery Replacement Instruction guide.

1. Begin by laying your Skygolf SG2 face down and remove the three recessed screws on the back.

2. Next carefully open the plug on the side of the SkyCaddie.

3. Next holding the GPS unit in your hand (with the screen facing downward) gently pull down the front plate of the unit and put the bottom half of the unit on a table with the belt clip facing down.

4. Next if there is a plastic bar on the right side push that upwards and then remove the battery. If no bar is present simply disconnect the old battery.

5. Replace the old battery by inserting and plugging in a brand new SkyGolf SG2 Battery from BatteryShip.com. Be certain to orient the new battery the same way the old one was oriented (at the bottom of where the circuit board is located; be sure to place the red wire on the left and set the wires along the top of the battery).

Now let's reverse our steps.

6. Place the front half of the GPS unit onto the back half and align the sides and connect them.

7. Carefully press the two halves together and replace the screws removed in step 1.

8. Place the rubber plug back in the right hand side of the Skygolf and charge your new battery for four hours. Then turn on your SG2.

Barnes and Noble Nook Battery Replacement Instructions

The following are the Barnes and Noble Nook Battery Replacement Instruction guide.

1. Begin by locating the small tab at the base of your nook.

2. Apply pressure on the tab then pull the cover off.

3. Next remove the screw securing the battery.

4. Pry out the original battery.

5. Replace the old battery with a new Barnes and Noble Nook Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original.

Now let's reverse our steps.

6. Replace and secure the battery by screwing in the screw.

7. Slide and replace the cover (gently snap in place).

8. Charge your new Barnes and Noble Nook Battery for four hours. Then turn on your on your Nook.

TomTom XXL540S Battery Replacement Instructions

The following are the TomTom XXL540S Battery Replacement Instruction guide.

1. Begin by lifitng the label at the base of the TomTom to access the screws underneath.

2. Remove the 2 screws.

3. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves.

3. Next remove the 3 screws securing the circuit board.

4. Now carefully lift the circuit board and disconnect the original battery.

5. Pry out the original battery.

6. Replace the old battery with a new TomTom XXL540S Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. Replace and secure the circuit board with the 3 screws you removed earlier in step 3.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in 2 screws removed in step 1 and 2.

9. Charge your TomTom XXL540S Battery for four hours. Then turn on.

Magellan Roadmate 1700 Battery Replacement Instructions

The following are the Magellan Roadmate 1700 Battery Replacement Instruction guide.

1. Begin by turning your Roadmate face down. On the back there will be a small grey rubber cover that is hiding a screw. Remove that screw. And then remove the screws in each of the 4 corners. Finally remove the 2 screws on the bottom of the Roadmate.

2. Next using the pry tool provided in your tool kit gently open the GPS by carefully separating the 2 halves (slide the pry tool all around the edge until the halves come apart). CAUTION as you open the the 2 sides (on the inside) they will be connected by cables. So please be careful not to rip apart the 2 halves.

3. Next remove the piece of tape and connectors from the circuit board to seperate the 2 halves.

4 Lift the piece of tape and disconnect the original battery. Pry out the origiginal battery.

5. Replace the old battery with a new Magellan Roadmate 1700 Battery from Batteryship.com and connect the battery to the circuit board (reapply the tape). Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

6. Re-attach the 2 connectors and secure them with the tape.

7. Now put the 2 halves of the GPS together and gently snap in place.

8. Screw in all 7 screws removed in step 1.

9. Charge your Magellan Roadmate 1700 Battery for four hours. Then turn on your Magellan.

TomTom VIA 1405M Battery Replacement Instructions

The following are the TomTom VIA 1405M Battery Replacement Instruction guide.

1. Begin by removing the suction cup mount. This can be done by twisting the mount and pulling it out.

2. Once the mount is removed you will be able to see a screw (where the mount ball was sitting). Remove this screw using the tools provided in your tool kit.

4. Next remove the 4 screws securing the circuitboard (the battery rests under the board).

5. Next gently remove or lift up the circuitboard.

6. Next disconnect the battery cable from the circuit board.

7. Replace the old battery with a new TomTom 1405M Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

8. Return the circuitboard to its original position and replace the screws to secure the circuitboard.

9. Now put the 2 halves of the GPs together and gently snap in place.

10. Screw in the screw removed in step 2.

11. Finally replace your mount and charge your TomTom VIA 1405M Battery for four hours. Then turn on your TomTom.

TomTom VIA 1405 Battery Replacement Instructions

The following are the TomTom VIA 1405 Battery Replacement Instruction guide.

1. Begin by removing the suction cup mount. This can be done by twisting the mount and pulling it out.

2. Once the mount is removed you will be able to see a screw (where the mount ball was sitting). Remove this screw using the tools provided in your tool kit.

4. Next remove the 4 screws securing the circuitboard (the battery rests under the board).

5. Next gently remove or lift up the circuitboard.

6. Next disconnect the battery cable from the circuit board.

7. Replace the old battery with a new TomTom 1405 Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

8. Return the circuitboard to its original position and replace the screws to secure the circuitboard.

9. Now put the 2 halves of the GPs together and gently snap in place.

10. Screw in the screw removed in step 2.

11. Finally replace your mount and charge your TomTom VIA 1405 Battery for four hours. Then turn on your TomTom.

TomTom VIA 1505 Battery Replacement Instructions

The following are the TomTom VIA 1505 Battery Replacement Instruction guide.

1. Begin by removing the suction cup mount. This can be done by twisting the mount and pulling it out.

2. Once the mount is removed you will be able to see a screw (where the mount ball was sitting). Remove this screw using the tools provided in your tool kit.

4. Next remove the 4 screws securing the circuitboard (the battery rests under the board).

5. Next gently remove or lift up the circuitboard.

6. Next disconnect the battery cable from the circuit board.

7. Replace the old battery with a new TomTom 1505 Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

8. Return the circuitboard to its original position and replace the screws to secure the circuitboard.

9. Now put the 2 halves of the GPs together and gently snap in place.

10. Screw in the screw removed in step 2.

11. Finally replace your mount and charge your TomTom VIA 1505 Battery for four hours. Then turn on your TomTom.

TomTom VIA 1405T Battery Replacement Instructions

The following are the TomTom VIA 1405T Battery Replacement Instruction guide.

1. Begin by removing the suction cup mount. This can be done by twisting the mount and pulling it out.

2. Once the mount is removed you will be able to see a screw (where the mount ball was sitting). Remove this screw using the tools provided in your tool kit.

4. Next remove the 4 screws securing the circuitboard (the battery rests under the board).

5. Next gently remove or lift up the circuitboard.

6. Next disconnect the battery cable from the circuit board.

7. Replace the old battery with a new TomTom 1405T Battery from Battership.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

8. Return the circuitboard to its original position and replace the screws to secure the circuitboard.

9. Now put the 2 halves of the GPs together and gently snap in place.

10. Screw in the screw removed in step 2.

11. Finally replace your mount and charge your TomTom VIA 1405T Battery for four hours. Then turn on your TomTom.

TomTom VIA 1535T Battery Replacement Instructions

The following are the TomTom VIA 1535T Battery Replacement Instruction guide.

1. Begin by removing the suction cup mount. This can be done by twisting the mount and pulling it out.

2. Once the mount is removed you will be able to see a screw (where the mount ball was sitting). Remove this screw using the tools provided in your tool kit.

4. Next remove the 4 screws securing the circuitboard (the battery rests under the board).

5. Next gently remove or lift up the circuitboard.

6. Next disconnect the battery cable from the circuit board.

7. Replace the old battery with a new TomTom 1535T Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original. It may be helpful to add a strip of double-sided tape in the battery compartment to help secure the battery in place so that it does not move around.

Now let's reverse our steps.

8. Return the circuitboard to its original position and replace the screws to secure the circuitboard.

9. Now put the 2 halves of the GPs together and gently snap in place.

10. Screw in the screw removed in step 2.

11. Finally replace your mount and charge your TomTom VIA 1535T Battery for four hours. Then turn on your TomTom.