Category: Battery Replacement Instructions – eBooks

Barnes and Nobel Nookcolor Battery Installation Instructions

The following instructions are the Barnes and Nobel Nookcolor battery installation instructions.

1. To begin lift the the microSD slot cover and remove the black sticker/tape that is under the cover to reveal 2 T5 screws. Remove the screws and set aside.

2. Next pry off the (using the pry tool provided in your tool kit from BatteryShip.com) the back cover of the Nook Color by sliding the pry tool around the edges of the back cover to lift the cover up. Once you get a portion of the cover lifted up the balance of the cover comes off pretty easily. Note small plastic tabs hold the cover in place.

3. Once the back cover is off lay your Nook Color face down. On the inside you will see that the majority of the space is taken up by the battery.

4. In order to replace the battery you must remove the large metal fame  that sits atop the display assembly. This internal metal frame also serves as the device's external edge. It is held to the display assembly with 10 Torx T5 screws. Remove these screws.

5. After removing the metal frame's 10 Torx T5 screws, you'll need to remove three rubber cushions that cover the connectors for the battery, and the power button, and volume up/down button. NOTE: the cushions are held in place with an adhesive. Using the pry tool or the thin metal flat head as a blade, you should be able to remove the cushions without tearing them or damaging the connector underneath. Just go slow here.

6. Now disconnect the battery.

7. You'll also need to disconnect the volume up/down button.

8. And disconnect the power button.

9. Now separate the display assembly from the metal frame. You can use the metal flat head or the pry tool or even a finger nail if long enough.

10. Now pry off the original battery. The NOOKcolor's battery is attached to the metal frame with two strips of double-sided tape. So it will take a little prying.

11. Replace the original Barnes and Nobel Nookcolor Battery with one from BatteryShip.com

Let's reverse our steps to complete the job…

12. Reset the metal frame onto the display assembly.

13. Connect the power button.

14. Connect the volume up/down button.

15. Connect the battery.

16. Reset the three rubber cushions that cover the connectors for the battery, and the power button, and volume up/down button. Remeber they were held in place with an adhesive….you may need to hold them in place with double sided tape.

17. Now screw in the 10 Torx T5 screws to hold together the the large metal fame  that sits atop the display assembly.

18. Snap in place the back cover.

19. Lastly screw in the 2 T5 screws under the microSD slot cover and reapply the black sticker/tape that will sit ontoip of the screws.
 
20. Charge your new Barnes and Nobel Nook Color Battery for 4 hours and then turn on.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300BC Battery Installation Instructions

The following are the Sony PRS-300BC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300BC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300BC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300RC Battery Installation Instructions

The following are the Sony PRS-300RC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300RC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300RC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300SC Battery Installation Instructions

The following are the Sony PRS-300SC Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300SC Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300SC Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-300 Battery Installation Instructions

The following are the Sony PRS-300 Battery Replacement Instruction guide.

1. Begin by removing all the screws at the top and base and back of your Sony.
 
2. Next using the pry tool remove the plastic frame/seal from the outside frame of the device.

3. Next detach the clips holding the back cover. Use your pry tool to help detach the clips. The clips hold the back cover in place.
 
4. Now remove the back cover.

5. Disconnect and remove the battery by using the pry tool to lift the battery up and out.

6. Replace the old battery with a brand new Sony PRS-300 Battery Replacement from BatteryShip.com.
 
Now let's reverse our steps.

7. Replace the back cover and snap into clips.

8. Carefully snap on the plastic frame/seal to the outside frame of the device.
 
9. Replace all the screws froma around the device.

10. Charge your Sony PRS-300 Battery for four hours. Then turn on your Sony.
 
PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle Keyboard Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle Keyboard Battery

1. Begin by turning your Amazon Kindle Keyboard face down. Placing your Kindle on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off back cover by detaching the clips that holds the cover on. You will need to slide the pry tool around the entire back cover. After the clips have been detached slide the cover downward and the cover will then come off.

3. Once the back cover is off you will see the inside of the Kindle and the battery.

4. Next remove the 2 screws securing the battery.

5. Remove the original battery.

6. Replace the original battery with the your new Amazon Kindle Keyboard Battery Replacement
from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place. You will need to be sure to snap the cover in completely.

9. Charge your new Kindle Keyboard Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all
instructions BEFORE replacing the battery.

Amazon Kindle Graphite Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle Graphite Battery

1. Begin by turning your Amazon Kindle Graphite face down. Placing your Kindle on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off back cover by detatching the clips that holds the cover on. You will need to slide the pry tool around the entire back cover. After the clips have been detached slide the cover downward and the cover will then come off.

3. Once the back cover is off you will see the inside of the Kindle and the battery.

4. Next remove the 2 screws securing the battery.

5. Remove the original battery.

6. Replace the original battery with the your new Amazon Kindle Graphite Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place. You will need to be sure to snap the cover in completely.

9. Charge your new Kindle Graphite Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Amazon Kindle Wi-Fi Battery Replacement Instructions

The following battery replacement instruction guide can be used for the following models:

Amazon Kindle Wi-Fi Battery

1. Begin by turning your Amazon Kindle Wi-Fi face down. Placing your Kindle on a soft cloth will help prevent the screen from being scratched.

2. Using your pry tool pry off back cover by detatching the clips that holds the cover on. You will need to slide the pry tool around the entire back cover. After the clips have been detached slide the cover downward and the cover will then come off.

3. Once the back cover is off you will see the inside of the Kindle and the battery.

4. Next remove the 2 screws securing the battery.

5. Remove the original battery.

6. Replace the original battery with the your new Amazon Kindle Wi-Fi Battery Replacement from BatteryShip.com

7. Replace the two screws to secure the battery.

8. Replace the cover and snap into place. You will need to be sure to snap the cover in completely.

9. Charge your new Kindle Wi-Fi Battery for at least 4 hours. Then turn on and use.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Barnes and Noble Nook Battery Replacement Instructions

The following are the Barnes and Noble Nook Battery Replacement Instruction guide.

1. Begin by locating the small tab at the base of your nook.

2. Apply pressure on the tab then pull the cover off.

3. Next remove the screw securing the battery.

4. Pry out the original battery.

5. Replace the old battery with a new Barnes and Noble Nook Battery from Batteryship.com and connect the battery to the circuit board. Be sure orient the new battery just as the original.

Now let's reverse our steps.

6. Replace and secure the battery by screwing in the screw.

7. Slide and replace the cover (gently snap in place).

8. Charge your new Barnes and Noble Nook Battery for four hours. Then turn on your on your Nook.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.

Sony PRS-505-LC Battery Replacement Instructions

The following are the Sony PRS-505-LC Battery Replacement Instruction guide.

1. Begin by laying your Sony face down so that the backside is facing you.

2. Next remove the 4 screws located on the back of your device (near all 4 corners of the
device)

3. Next – on the bottom of the eReader there will be a screw near the corner (opposite of
the input/connector slots). Loosen this screw. The screw will remain connected to the
reader but it does need to be loosened in order to separate the 2 halves.

4. Now using the pry tool provided in your kit gently remove the bottom external frame
(this is the metal frame that covers the input slots).

5. Once the metal cover has been removed you will see 3 screws. Remove these screws. Next
remove the back cover to reveal the inside of your Sony and the battery.

6. Next turn the eReader over and remove any SD Cards from the device.

7. Once the SD Cards are removed then using the pry tool remove the metal frame that covers
the SD Slots.

8. Next using the flat head screwdriver provided lift off the 2 clips from the top of the
device.

9. Turn the eReader over and use the pry tool to push out the eReader from its cover. Push
it out just far enough so that you can access the ribbon cable.

10. Disconnect Ribbon cable.

11. Then pull the internal part of eReader out of its frame until you can see the battery.

12. Use the pry tool to lift up the old battery and disconnect it and remove from the
battery compartment.

13. Replace the old battery with a brand new Sony PRS-505-LC Battery Replacement from

BatteryShip.com. When replacing the battery be sure to push down the battery cables below the

circuit board surface.

14. Now let's reverse our steps. Carefully push back in the internal portion iof eReader
back into the frame. Only go half way since we need to reconnect the ribbon cable.

15. Connect the ribbon cable. Be sure it is secure.

16. Continue pushing in the eReader till it is back in position.

17. Return the 2 clips to their original positions.

18. Replace the top metal frame cover.

19. Return the 3 screws to the bottom of the device.

20. Snap the bottom metal frame cover in place and tighten the screw to secure the frame
into place.

21. Insert any SD cards back into their respective slots and replace the 4 screws on the
back of the eReader.

22. Charge your Sony PRS-505-LC Battery for four hours. Then turn on your Sony.

PLEASE NOTE: Patience and care, along with moderate technical and hand tool ability, are required for the successful replacement of a battery. Excessive force may result in damage to your device. The instructions above come with no warranty or guarantee. By utilizing these instructions, you agree to hold Batteryship.com and BatteryEducation.com blameless and unaccountable for any and all damages, problems, or personal injuries that may or may not arise by your use of these instructions. Replacing your battery may void any warranty you have on your device. Please read all instructions BEFORE replacing the battery.